Archive for 'Leaking Garbage Disposal'

Fix Garbage Disposal
How To Fix That Garbage Disposal

3 Easy Garbage Disposal How To Tips

Discover some fix garbage disposal how to tips and learn how easy it is to keep your appliance running smoothly. Find out what to do when your appliance will not turn on, will not shred garbage, or drains slowly. Also, learn two simple tricks that can help keep your garbage disposal operating at its best.

The first thing to always remember when working on a garbage disposal is, by no means ever put your hand inside the component. It can be unplugged, turned off, and the breaker switch turned off, you still never put your hand inside. Doing it once with no incident can make a person feel safe enough to do it again which can result in injury.

One thing that happens often, is the unit will not turn on.

You flip the switch and nothing happens, there is no humming, no sound, nothing. Check the plug and make certain it is plugged in. If the plug is secure, then try the reset button. If that still does not work, check the electrical panel to find out if the breaker has been switched off. If none of these suggestions resolves the problem, then either the switch or the disposal needs to be replaced.

Sometimes the unit will turn on but instead of shredding garbage it will just hum, which means the flywheel is stuck.

Something has wrapped itself around the the shredder ring and impeller which is preventing the flywheel from turning. To solve this, first turn off the power to the component. Then insert a wooden broom handle in the drain and apply pressure to the impeller. When the flywheel dislodges, you will be able to feel it turn.

Another solution is to use the offset wrench that came with the component when it was purchased. After turning the power to the unit off, insert the wrench into the hole you will find on the bottom side of the appliance. Turn it clockwise and you should feel the wheels free themselves. Press the reset button and run some water into the unit. After a few moments, turn it on and let it run long enough to shred the item that had jammed it.

Clogs and slow drains can also occur.

First, never apply chemical drain cleaners to the garbage disposal as it will damage it. Turn off the power to the unit then remove its discharge pipe and the drain trap. Remove any grease build up or other obstructions in the line. If you cannot see any, then the obstruction is behind the wall and you will need to use an auger to free it.

There are two things you can do to keep your component running smoothly. One is to put ice cubes in the drain and turn the unit on. Shredding the ice will sharpen the blades while it clears away build up. Another thing that will help your unit run efficiently is to let one cup of vinegar stand inside it for an hour. Run very hot water and any muck that has built up will wash down the drain.

These simple fix garbage disposal how to tips do not take much time and practically no money.

Combined with the two maintenance tips, your unit should run smoothly for years. Remember also to never put your hands into the unit and never use chemical drain cleaners on the units.

Fix Garbage Disposal,Garbage Disposal Problems,Repair Garbage Disposal,Leaking Garbage Disposal,Replace Garbage Disposal,Fix Garbage Disposal Clogged,Fix Garbage Disposal Leak

Install Garbage Disposal

Install Garbage DisposalHow To Install Garbage Disposal Personally Or Just Use a Professional

A garbage disposal unit is one of the hardest working appliances in a home. It is good to make sure you follow the best possible method for installing it which will give you years of problem-free service from a piece of equipment that gets a real workout. When uncertain about whether you should install garbage disposal yourself or just use a pro, here are some details to consider. Take the time to read the following article carefully before you make up your mind.

The kitchen scraps need to be fine enough to pass through a drainage pipe.

In order to do that, the different mechanical parts of the garbage disposal team up to provide an extremely rapid chopping and grinding action. Known as the shredder ring and the impellers or blades, these parts swing into action when the switch is flipped activating the motor. Originally, the food scraps are collected in a separate section of the unit. Once the power is on, the food scraps are forced through the chopper ring and ground fine by the impellers. This action continues until everything is almost liquefied and ready to be flushed down the drainage pipe with tap water.

If you want to get a motor that is powerful enough to grind food scraps very fine, it might be advisable to get a unit with a three-quarter horsepower motor.

Some professionals say that a one-half horsepower motor is enough. But the main thing to be sure of is that you have a motor that is powerful enough to do the job thoroughly.

There is always the risk of unknowingly running the equipment too long. Without a reset button, the motor and wiring could easily burn. So a reset button is a worthwhile prerequisite to look for when you are shopping for a unit.

There is always the possibility that a stubborn piece of food scraps gets jammed causing everything to freeze up. That is why it is advisable to look for one that has a shredder ring that can be manually worked.

One of the main considerations is being sure to have a power source and electrical outlet in close proximity to where you plan to use your unit.

Although the installation procedure can be pretty straightforward, it is advisable to know something about wiring and plumbing.

Before replacing the sink flange, the metal edge that protrudes from the bottom of the sink, with one from the unit, it is crucial to follow the safety rules about working with electricity. The main one being to be sure that there is no electrical power running through the lines. You might even want to throw the breaker switch before starting.

At this point, you might want to consider whether to get some professional installer to make sure that everything is fitted correctly. Even though installation may seem pretty simple, without any electrical or plumbing know-how, you could do a faulty job without knowing it.

Another important consideration is making sure the electrical wires are attached in the right sequence to your house wires. If this is not done correctly, a short or even electrical fire could result. In any case, if you do decide to do the job yourself, the wires for the unit are located beneath the plate on the bottom. Once you have located these and connected them, the electric wiring job is done.

It is important to check that all the joins are secure and not leaking once the discharge tube of the unit has been connected to the sink drainage pipe.

Even though installing a disposal unit may appear to be a fairly easy process, the results could be disastrous if you do not have any experience with wiring or plumbing.

So after reading this entire article, you may find yourself trying to decide whether to install garbage disposal yourself or just use a pro. Take time to consider what will work best in your particular situation. You may find that calling on a professional may cost you less headache and repairs in the long run.

Install Garbage Disposal with Dishwasher,Install Garbage Disposal Double Sink,Install Garbage Disposal to Sink,Install Garbage Disposal Drain

 
Boulder County Plumbing
1016 Stearns Ave
Boulder, CO 80303

Payments accepted:
Cash, Check
Google Places